getting-started.md

Getting started guide

Thanks for trying Netdata! In this guide, we'll quickly walk you through the first steps you should take after getting Netdata installed.

Netdata can collect thousands of metrics in real-time without any configuration, but there are some valuable things to know to get the most of out Netdata based on your needs.

If you haven't installed Netdata yet, visit the installation instructions for details, including our one-liner script, which automatically installs Netdata on almost all Linux distributions.

Access the dashboard

Open up your web browser of choice and navigate to http://YOUR-HOST:19999. Welcome to Netdata!

What's next?:

• Read more about the standard Netdata dashboard.
• Learn all the specifics of using charts or the differences between charts, context, and families.

Configuration basics

Netdata primarily uses the netdata.conf file for custom configurations.

On most systems, you can find that file at /etc/netdata/netdata.conf.

Some operating systems will place your netdata.conf at /opt/netdata/etc/netdata/netdata.conf, so check there if you find nothing at /etc/netdata/netdata.conf.

The netdata.conf file is broken up into various sections, such as [global], [web], [registry], and more. By default, most options are commented, so you'll have to uncomment them (remove the #) for Netdata to recognize your change.

Once you save your changes, restart Netdata to load your new configuration.

What's next?:

• Change how long Netdata stores metrics by either increasing the history option or switching to the database engine.
• Move Netdata's dashboard to a different port or enable TLS/HTTPS encryption.
• See all the netdata.conf options in our daemon configuration documentation.
• Run your own registry.

Collect data from more sources

When Netdata starts, it auto-detects dozens of data sources, such as database servers, web servers, and more. To auto-detect and collect metrics from a service or application you just installed, you need to restart Netdata.

There is one exception: When Netdata is running on the host (as in not in a container itself), it will always auto-detect containers and VMs.

However, auto-detection only works if you installed the source using its standard installation procedure. If Netdata isn't collecting metrics after a restart, your source probably isn't configured correctly. Look at the external plugin documentation to find the appropriate module for your source. Those pages will contain more information about how to configure your source for auto-detection.

Some modules, like chrony, are disabled by default and must be enabled manually for auto-detection to work.

Once Netdata detects a valid source of data, it will continue trying to collect data from it. For example, if Netdata is collecting data from an Nginx web server, and you shut Nginx down, Netdata will collect new data as soon as you start the web server back up—no restart necessary.

Configuring plugins

Even if Netdata auto-detects your service/application, you might want to configure what, or how often, Netdata is collecting data.

Netdata uses internal and external plugins to collect data. Internal plugins run within the Netdata dæmon, while external plugins are independent processes that send metrics to Netdata over pipes. There are also plugin orchestrators, which are external plugins with one or more data collection modules.

You can configure both internal and external plugins, along with the individual modules. There are many ways to do so:

• In netdata.conf, [plugins] section: Enable or disable internal or external plugins with yes or no.
• In netdata.conf, [plugin:XXX] sections: Each plugin has a section for changing collection frequency or passing options to the plugin.
• In .conf files for each external plugin: For example, at /etc/netdata/python.d.conf.
• In .conf files for each module : For example, at /etc/netdata/python.d/nginx.conf.

It's complex, so let's walk through an example of the various .conf files responsible for collecting data from an Nginx web server using the nginx module and the python.d plugin orchestrator.

First, you can enable or disable the python.d plugin entirely in netdata.conf.

[plugins]
    # Enabled
    python.d = yes
    # Disabled
    python.d = no

You can also configure the entire python.d external plugin via the [plugin:python.d] section in netdata.conf. Here, you can change how often Netdata uses python.d to collect metrics or pass other command options:

[plugin:python.d]
    update every = 1
    command options = 

The python.d plugin has a separate configuration file at /etc/netdata/python.d.conf for enabling and disabling modules. You can use the edit-config script to edit the file, or open it with your text editor of choice:

sudo /etc/netdata/edit-config python.d.conf

Finally, the nginx module has a configuration file called nginx.conf in the python.d folder. Again, use edit-config or your editor of choice:

sudo /etc/netdata/edit-config python.d/nginx.conf

In the nginx.conf file, you'll find additional options. The default works in most situations, but you may need to make changes based on your particular Nginx setup.

What's next?:

• Look at the full list of data collection modules to configure your sources for auto-detection and monitoring.
• Improve the performance of Netdata on low-memory systems.
• Configure systemd to expose systemd services utilization metrics automatically.
• Reconfigure individual charts in netdata.conf.

Health monitoring and alarms

Netdata comes with hundreds of health monitoring alarms for detecting anomalies on production servers. If you're running Netdata on a workstation, you might want to disable Netdata's alarms.

Edit your /etc/netdata/netdata.conf file and set the following:

[health]
    enabled = no

If you want to keep health monitoring enabled, but turn email notifications off, edit your health_alarm_notify.conf file with edit-config, or with your the text editor of your choice:

sudo /etc/netdata/edit-config health_alarm_notify.conf

Find the SEND_EMAIL="YES" line and change it to SEND_EMAIL="NO".

What's next?:

• Write your own health alarm using the examples.
• Add a new notification method, like Slack.

Change how long Netdata stores metrics

By default, Netdata uses a custom database which uses both RAM and the disk to store metrics. Recent metrics are stored in the system's RAM to keep access fast, while historical metrics are "spilled" to disk to keep RAM usage low.

This custom database, which we call the database engine, allows you to store a much larger dataset than your system's available RAM.

If you're not sure whether you're using the database engine, or want to tweak the default settings to store even more historical metrics, check out our tutorial: Changing how long Netdata stores metrics.

What's next?:

• Learn more about the memory requirements for the database engine to understand how much RAM/disk space you should commit to storing historical metrics.
• Read up on the memory requirements of the round-robin database, or figure out whether your system has KSM enabled, which can reduce the default database's memory usage by about 60%.

Monitoring multiple systems with Netdata

If you have Netdata installed on multiple systems, you can have them all appear in the My nodes menu at the top-left corner of the dashboard.

To show all your servers in that menu, you need to register for or sign in to Netdata Cloud from each system. Each system will then appear in the My nodes menu, which you can use to navigate between your systems quickly.

Whenever you pan, zoom, highlight, select, or pause a chart, Netdata will synchronize those settings with any other agent you visit via the My nodes menu. Even your scroll position is synchronized, so you'll see the same charts and respective data for easy comparisons or root cause analysis.

You can now seamlessly track performance anomalies across your entire infrastructure!

What's next?:

• Read up on how the Netdata Cloud registry works, and what kind of data it stores and sends to your web browser.
• Familiarize yourself with the Nodes View

Start, stop, and restart Netdata

When you install Netdata, it's configured to start at boot, and stop and restart/shutdown. You shouldn't need to start or stop Netdata manually, but you will probably need to restart Netdata at some point.

• To start Netdata, open a terminal and run service netdata start.
• To stop Netdata, run service netdata stop.
• To restart Netdata, run service netdata restart.

The service command is a wrapper script that tries to use your system's preferred method of starting or stopping Netdata based on your system. But, if either of those commands fails, try using the equivalent commands for systemd and init.d:

• systemd: systemctl start netdata, systemctl stop netdata, systemctl restart netdata
• init.d: /etc/init.d/netdata start, /etc/init.d/netdata stop, /etc/init.d/netdata restart

What's next?

Even after you've configured netdata.conf, tweaked alarms, learned the basics of performance troubleshooting, and added all your systems to the My nodes menu, you've just gotten started with Netdata.

Take a look at some more advanced features and configurations:

• Centralize Netdata metrics from many systems with streaming
• Enable long-term archiving of Netdata metrics via backends to time-series databases.
• Improve security by putting Netdata behind an Nginx proxy with SSL.

Or, learn more about how you can contribute to Netdata core or our documentation!