qwiic_bme280.py

#-----------------------------------------------------------------------------
# qwiic_bme280.py
#
# Python library for the SparkFun qwiic BME280 sensor.
#
# This sensor is available on the SparkFun Environmental Combo Breakout board.
#   https://www.sparkfun.com/products/14348
#
#------------------------------------------------------------------------
#
# Written by  SparkFun Electronics, May 2019
#
# This python library supports the SparkFun Electroncis qwiic
# qwiic sensor/board ecosystem
#
# More information on qwiic is at https:// www.sparkfun.com/qwiic
#
# Do you like this library? Help support SparkFun. Buy a board!
#==================================================================================
# Copyright (c) 2019 SparkFun Electronics
#
# Permission is hereby granted, free of charge, to any person obtaining a copy
# of this software and associated documentation files (the "Software"), to deal
# in the Software without restriction, including without limitation the rights
# to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
# copies of the Software, and to permit persons to whom the Software is
# furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in all
# copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
# AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
# LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
# OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#==================================================================================
#
# This is mostly a port of existing Arduino functionaly, so pylint is sad.
# The goal is to keep the public interface pthonic, but internal is internal
#
# pylint: disable=line-too-long, bad-whitespace, invalid-name, too-many-public-methods
#

"""!
qwiic_bme280
============
Python module for the qwiic bme280 sensor, which is part of the [SparkFun Qwiic Environmental Combo Breakout](https://www.sparkfun.com/products/14348)

This python package is a port of the existing [SparkFun BME280 Arduino Library](https://github.com/sparkfun/SparkFun_BME280_Arduino_Library)

This package can be used in conjunction with the overall [SparkFun qwiic Python Package](https://github.com/sparkfun/Qwiic_Py)

New to qwiic? Take a look at the entire [SparkFun qwiic ecosystem](https://www.sparkfun.com/qwiic).
"""

#-----------------------------------------------------------------------------
import math
import time
import qwiic_i2c

# Define the device name and I2C addresses. These are set in the class defintion
# as class variables, making them avilable without having to create a class instance.
# This allows higher level logic to rapidly create a index of qwiic devices at
# runtine
#
# The name of this device
_DEFAULT_NAME = "Qwiic BME280"

# Some devices have multiple availabel addresses - this is a list of these addresses.
# NOTE: The first address in this list is considered the default I2C address for the
# device.
_AVAILABLE_I2C_ADDRESS = [0x77, 0x76]

# Default Setting Values
_settings = {"runMode" : 3,         \
            "tStandby"  : 0,        \
            "filter"    : 0,        \
            "tempOverSample"  : 1,  \
            "pressOverSample" : 1,  \
            "humidOverSample" : 1,  \
            "tempCorrection"  : 0.0}

# define our valid chip IDs
_validChipIDs = [0x58, 0x60]

# define the class that encapsulates the device being created. All information associated with this
# device is encapsulated by this class. The device class should be the only value exported
# from this module.

class QwiicBme280(object):
    """!
    QwiicBme280

    @param address: The I2C address to use for the device.
                        If not provided, the default address is used.
    @param i2c_driver: An existing i2c driver object. If not provided
                        a driver object is created.

    @return **Object** The BME280 device object.
    """
    # Constructor
    device_name         =_DEFAULT_NAME
    available_addresses = _AVAILABLE_I2C_ADDRESS

    # mode flags for the device - user exposed
    MODE_SLEEP = 0b00
    MODE_FORCED = 0b01
    MODE_NORMAL = 0b11

    # Register names for the BME280
    BME280_DIG_T1_LSB_REG =         0x88
    BME280_DIG_T1_MSB_REG =         0x89
    BME280_DIG_T2_LSB_REG =         0x8A
    BME280_DIG_T2_MSB_REG =         0x8B
    BME280_DIG_T3_LSB_REG =         0x8C
    BME280_DIG_T3_MSB_REG =         0x8D
    BME280_DIG_P1_LSB_REG =         0x8E
    BME280_DIG_P1_MSB_REG =         0x8F
    BME280_DIG_P2_LSB_REG =         0x90
    BME280_DIG_P2_MSB_REG =         0x91
    BME280_DIG_P3_LSB_REG =         0x92
    BME280_DIG_P3_MSB_REG =         0x93
    BME280_DIG_P4_LSB_REG =         0x94
    BME280_DIG_P4_MSB_REG =         0x95
    BME280_DIG_P5_LSB_REG =         0x96
    BME280_DIG_P5_MSB_REG =         0x97
    BME280_DIG_P6_LSB_REG =         0x98
    BME280_DIG_P6_MSB_REG =         0x99
    BME280_DIG_P7_LSB_REG =         0x9A
    BME280_DIG_P7_MSB_REG =         0x9B
    BME280_DIG_P8_LSB_REG =         0x9C
    BME280_DIG_P8_MSB_REG =         0x9D
    BME280_DIG_P9_LSB_REG =         0x9E
    BME280_DIG_P9_MSB_REG =         0x9F
    BME280_DIG_H1_REG =             0xA1
    BME280_CHIP_ID_REG =            0xD0 # Chip ID
    BME280_RST_REG =                0xE0 # Softreset Reg
    BME280_DIG_H2_LSB_REG =         0xE1
    BME280_DIG_H2_MSB_REG =         0xE2
    BME280_DIG_H3_REG =             0xE3
    BME280_DIG_H4_MSB_REG =         0xE4
    BME280_DIG_H4_LSB_REG =         0xE5
    BME280_DIG_H5_MSB_REG =         0xE6
    BME280_DIG_H6_REG =             0xE7
    BME280_CTRL_HUMIDITY_REG =      0xF2 # Ctrl Humidity Reg
    BME280_STAT_REG =               0xF3 # Status Reg
    BME280_CTRL_MEAS_REG =          0xF4 # Ctrl Measure Reg
    BME280_CONFIG_REG =             0xF5 # Configuration Reg
    BME280_PRESSURE_MSB_REG =       0xF7 # Pressure MSB
    BME280_PRESSURE_LSB_REG =       0xF8 # Pressure LSB
    BME280_PRESSURE_XLSB_REG =      0xF9 # Pressure XLSB
    BME280_TEMPERATURE_MSB_REG =    0xFA # Temperature MSB
    BME280_TEMPERATURE_LSB_REG =    0xFB # Temperature LSB
    BME280_TEMPERATURE_XLSB_REG =   0xFC # Temperature XLSB
    BME280_HUMIDITY_MSB_REG =       0xFD # Humidity MSB
    BME280_HUMIDITY_LSB_REG =       0xFE # Humidity LSB

    # Constructor
    def __init__(self, address=None, i2c_driver=None):

        # Did the user specify an I2C address?
        if address in self.available_addresses:
            self.address = address
        else:
            self.address = self.available_addresses[0]

        # load the I2C driver if one isn't provided

        if i2c_driver is None:
            self._i2c = qwiic_i2c.getI2CDriver()
            if self._i2c is None:
                print("Unable to load I2C driver for this platform.")
                return
        else:
            self._i2c = i2c_driver


        # create a dictionary to stash our calibration data for the sensor
        self.calibration={}

        self.t_fine=0

        self._referencePressure = 101325.0

    # ----------------------------------
    # is_connected()
    #
    # Is an actual board connected to our system?

    def is_connected(self):
        """!
        Determine if a BME280 device is conntected to the system..

        @return **bool** True if the device is connected, otherwise False.
        """
        return self._i2c.isDeviceConnected(self.address)

    connected = property(is_connected)

    # ----------------------------------
    # begin()
    #
    # Initialize the system/validate the board.
    def begin(self):
        """!
        Initialize the operation of the BME280 module

        @return **bool** Returns true of the initializtion was successful, otherwise False.
        """
        # are we who we need to be?
        chipID = self._i2c.readByte(self.address, self.BME280_CHIP_ID_REG)
        if chipID not in _validChipIDs:
            print("Invalid Chip ID: 0x%.2X" % chipID)
            return False
        

        def unsigned_short_to_signed_short(n): 
            """!
            Converts a 2 byte unsigned short to signed short (uint16_t -> int16_t)

            @param n: Unsigned short (uint16_t) to convert

            @return **int** Signed short (int16_t)
            """
            assert n >= 0, "Expected number to be unsigned (uint16_t), n>=0"
            assert n <= 2**16 - 1,"Expected number to be short (int16_t), n <= 2^16 - 1"

            return n - 2**16 if n >= 2**15 else n

        def unsigned_char_to_signed_char(n):
            """!
            Converts an unsigned char to signed char (uint8_t -> int8_t)

            @param n: Unsigned char (uint8_t) to convert

            @return **int** Signed char (int8_t)
            """
            assert n >= 0, "Expected number to be unsigned (uint8_t), n>=0"
            assert n <= 2**8 - 1,"Expected number to be char (int8_t), n <= 2^8 - 1"

            return n - 2**8 if n >= 2**7 else n

        # Reading all compensation data, range 0x88:A1, 0xE1:E7
        self.calibration["dig_T1"] = (self._i2c.readByte(self.address, self.BME280_DIG_T1_MSB_REG) << 8) + self._i2c.readByte(self.address, self.BME280_DIG_T1_LSB_REG)
        self.calibration["dig_T2"] = unsigned_short_to_signed_short((self._i2c.readByte(self.address, self.BME280_DIG_T2_MSB_REG) << 8) + self._i2c.readByte(self.address, self.BME280_DIG_T2_LSB_REG))
        self.calibration["dig_T3"] = unsigned_short_to_signed_short((self._i2c.readByte(self.address, self.BME280_DIG_T3_MSB_REG) << 8) + self._i2c.readByte(self.address, self.BME280_DIG_T3_LSB_REG))

        self.calibration["dig_P1"] = (self._i2c.readByte(self.address, self.BME280_DIG_P1_MSB_REG) << 8) + self._i2c.readByte(self.address, self.BME280_DIG_P1_LSB_REG)
        self.calibration["dig_P2"] = unsigned_short_to_signed_short((self._i2c.readByte(self.address, self.BME280_DIG_P2_MSB_REG) << 8) + self._i2c.readByte(self.address, self.BME280_DIG_P2_LSB_REG))
        self.calibration["dig_P3"] = unsigned_short_to_signed_short((self._i2c.readByte(self.address, self.BME280_DIG_P3_MSB_REG) << 8) + self._i2c.readByte(self.address, self.BME280_DIG_P3_LSB_REG))
        self.calibration["dig_P4"] = unsigned_short_to_signed_short((self._i2c.readByte(self.address, self.BME280_DIG_P4_MSB_REG) << 8) + self._i2c.readByte(self.address, self.BME280_DIG_P4_LSB_REG))
        self.calibration["dig_P5"] = unsigned_short_to_signed_short((self._i2c.readByte(self.address, self.BME280_DIG_P5_MSB_REG) << 8) + self._i2c.readByte(self.address, self.BME280_DIG_P5_LSB_REG))
        self.calibration["dig_P6"] = unsigned_short_to_signed_short((self._i2c.readByte(self.address, self.BME280_DIG_P6_MSB_REG) << 8) + self._i2c.readByte(self.address, self.BME280_DIG_P6_LSB_REG))
        self.calibration["dig_P7"] = unsigned_short_to_signed_short((self._i2c.readByte(self.address, self.BME280_DIG_P7_MSB_REG) << 8) + self._i2c.readByte(self.address, self.BME280_DIG_P7_LSB_REG))
        self.calibration["dig_P8"] = unsigned_short_to_signed_short((self._i2c.readByte(self.address, self.BME280_DIG_P8_MSB_REG) << 8) + self._i2c.readByte(self.address, self.BME280_DIG_P8_LSB_REG))
        self.calibration["dig_P9"] = unsigned_short_to_signed_short((self._i2c.readByte(self.address, self.BME280_DIG_P9_MSB_REG) << 8) + self._i2c.readByte(self.address, self.BME280_DIG_P9_LSB_REG))

        self.calibration["dig_H1"] = self._i2c.readByte(self.address, self.BME280_DIG_H1_REG)
        self.calibration["dig_H2"] = unsigned_short_to_signed_short((self._i2c.readByte(self.address, self.BME280_DIG_H2_MSB_REG) << 8) + self._i2c.readByte(self.address, self.BME280_DIG_H2_LSB_REG))
        self.calibration["dig_H3"] = self._i2c.readByte(self.address, self.BME280_DIG_H3_REG)
        self.calibration["dig_H4"] = unsigned_short_to_signed_short((self._i2c.readByte(self.address, self.BME280_DIG_H4_MSB_REG) << 4) + (self._i2c.readByte(self.address, self.BME280_DIG_H4_LSB_REG) & 0x0F))
        self.calibration["dig_H5"] = unsigned_short_to_signed_short((self._i2c.readByte(self.address, self.BME280_DIG_H5_MSB_REG) << 4) + ((self._i2c.readByte(self.address, self.BME280_DIG_H4_LSB_REG) >> 4) & 0x0F))
        self.calibration["dig_H6"] = unsigned_char_to_signed_char(self._i2c.readByte(self.address, self.BME280_DIG_H6_REG))

        # Most of the time the sensor will be init with default values
        # But in case user has old/deprecated code, use the _settings.x values

        self.set_standby_time(_settings["tStandby"])
        self.set_filter(_settings["filter"])
        self.set_pressure_oversample(_settings["pressOverSample"]) # Default of 1x oversample
        self.set_humidity_oversample(_settings["humidOverSample"]) # Default of 1x oversample
        self.set_tempature_oversample(_settings["tempOverSample"]) # Default of 1x oversample

        self.set_mode(self.MODE_NORMAL) #Go!

        # Wait for first measurement to come through. According to the second
        # equation in section 9.1 of the datasheet, it should take no longer
        # than 9.3ms to finish the first measurement at 1x oversampling on all
        # sensors. So wat 10ms to be safe
        time.sleep(0.01)

        return True

    #----------------------------------------------------------------
    # Mode of the sensor

    def set_mode(self, mode):
        """!
        Set the operational mode of the sensor.

        @param mode: One of the class constant values.
                    MODE_SLEEP, MODE_FORCED, MODE_NORMAL

        @return No return value
        """
        if mode > 0b11:
            mode = 0  # Error check. Default to sleep mode

        controlData = self._i2c.readByte(self.address, self.BME280_CTRL_MEAS_REG)
        controlData &= (~( (1<<1) | (1<<0) ) ) & 0xFF # Clear the mode[1:0] bits - note we just want a byte
        controlData |= mode   # Set
        self._i2c.writeByte(self.address, self.BME280_CTRL_MEAS_REG, controlData)


    def get_mode(self):
        """!
        Returns the operational mode of the sensor.

        @return **MODE_SLEEP, MODE_FORCED, or MODE_NORMAL** The current operational mode
        """
        controlData = self._i2c.readByte(self.address, self.BME280_CTRL_MEAS_REG)
        return controlData & 0b00000011

    # Make the mode a property of this object
    mode = property(get_mode, set_mode)

    #----------------------------------------------------------------
    # Set the standby bits in the config register
    # tStandby can be:
    #   0, 0.5ms
    #   1, 62.5ms
    #   2, 125ms
    #   3, 250ms
    #   4, 500ms
    #   5, 1000ms
    #   6, 10ms
    #   7, 20ms
    def set_standby_time(self, timeSetting):
        """!
        Set the standby bits in the BME280s config register

        @param timeSetting: The standby time bits - acceptable values
                        0 = 0.5ms
                        1 = 62.5ms
                        2 = 125ms
                        3 = 250ms
                        4 = 500ms
                        5 = 1000ms
                        6 = 10ms
                        7 = 20ms

        @return No return value
        """

        if timeSetting > 0b111 :
            timeSetting = 0 # Error check. Default to 0.5ms

        controlData = self._i2c.readByte(self.address, self.BME280_CONFIG_REG)
        controlData &= ( ~( (1<<7) | (1<<6) | (1<<5) )) & 0xff # Clear the 7/6/5 bits
        controlData |= (timeSetting << 5) # Align with bits 7/6/5
        self._i2c.writeByte(self.address, self.BME280_CONFIG_REG, controlData)

    # Make standby time a property
    standby_time = property()
    standby_time = standby_time.setter(set_standby_time)

    #----------------------------------------------------------------
    # Set the filter bits in the config register
    # filter can be off or number of FIR coefficients to use:
    #   0, filter off
    #   1, coefficients = 2
    #   2, coefficients = 4
    #   3, coefficients = 8
    #   4, coefficients = 16
    def set_filter(self, filterSetting):
        """!
        Set the filter bits in the BME280s config register

        @param filterSetting: The filter bits for the BME280. Acceptable values
                        0 = filter off
                        1 = coefficients = 2
                        2 = coefficients = 4
                        3 = coefficients = 8
                        4 = coefficients = 16

        @return No return value
        """
        if filterSetting > 0b111 :
            filterSetting = 0 # Error check. Default to filter off

        controlData = self._i2c.readByte(self.address, self.BME280_CONFIG_REG)
        controlData &= (~( (1<<4) | (1<<3) | (1<<2) ) ) & 0xFF # Clear the 4/3/2 bits
        controlData |= (filterSetting << 2) # Align with bits 4/3/2
        self._i2c.writeByte(self.address, self.BME280_CONFIG_REG, controlData)

    filter = property()
    filter = filter.setter(set_filter)

    #----------------------------------------------------------------
    # Set the temperature oversample value
    # 0 turns off temp sensing
    # 1 to 16 are valid over sampling values
    def set_tempature_oversample(self, overSampleAmount):
        """!
        Set the temperature oversample value

        @param overSampleAmount: The temperature oversample value. Acceptable values
                0 = turns off temp sensing
                1 to 16 are valid over sampling values

        @return No return value
        """
        overSampleAmount = self.check_sample_value(overSampleAmount) # Error check

        originalMode = self.get_mode() # Get the current mode so we can go back to it at the end

        self.set_mode(self.MODE_SLEEP) # Config will only be writeable in sleep mode, so first go to sleep mode

        # Set the osrs_t bits (7, 6, 5) to overSampleAmount
        controlData = self._i2c.readByte(self.address, self.BME280_CTRL_MEAS_REG)
        controlData &= (~( (1<<7) | (1<<6) | (1<<5) )) & 0xFF # Clear bits 765
        controlData |= overSampleAmount << 5 # Align overSampleAmount to bits 7/6/5
        self._i2c.writeByte(self.address, self.BME280_CTRL_MEAS_REG, controlData)

        self.set_mode(originalMode) # Return to the original user's choice

    tempature_oversample = property()
    tempature_oversample = tempature_oversample.setter(set_tempature_oversample)

    # Set the pressure oversample value
    # 0 turns off pressure sensing
    # 1 to 16 are valid over sampling values
    def set_pressure_oversample(self, overSampleAmount):
        """!
        Set the pressure oversample value

        @param overSampleAmount: The pressure oversample value. Acceptable values
                0 = turns off pressure sensing
                1 to 16 are valid over sampling values

        @return No return value
        """
        overSampleAmount = self.check_sample_value(overSampleAmount) # Error check

        originalMode = self.get_mode() # Get the current mode so we can go back to it at the end

        self.set_mode(self.MODE_SLEEP) # Config will only be writeable in sleep mode, so first go to sleep mode

        # Set the osrs_p bits (4, 3, 2) to overSampleAmount
        controlData = self._i2c.readByte(self.address, self.BME280_CTRL_MEAS_REG)
        controlData &= (~( (1<<4) | (1<<3) | (1<<2) )) & 0xFF  # Clear bits 432
        controlData |= overSampleAmount << 2 # Align overSampleAmount to bits 4/3/2
        self._i2c.writeByte(self.address, self.BME280_CTRL_MEAS_REG, controlData)

        self.set_mode(originalMode) # Return to the original user's choice

    pressure_oversample = property()
    pressure_oversample = pressure_oversample.setter(set_pressure_oversample)

    #----------------------------------------------------------------
    # Set the humidity oversample value
    # 0 turns off humidity sensing
    # 1 to 16 are valid over sampling values
    def set_humidity_oversample(self, overSampleAmount):
        """!
        Set the humidity oversample value

        @param overSampleAmount: The humidity oversample value. Acceptable values
                0 = turns off humidity sensing
                1 to 16 are valid over sampling values

        @return No return value
        """
        overSampleAmount = self.check_sample_value(overSampleAmount) # Error check

        originalMode = self.get_mode() # Get the current mode so we can go back to it at the end

        self.set_mode(self.MODE_SLEEP) # Config will only be writeable in sleep mode, so first go to sleep mode

        # Set the osrs_h bits (2, 1, 0) to overSampleAmount
        controlData = self._i2c.readByte(self.address, self.BME280_CTRL_HUMIDITY_REG)
        controlData &= (~( (1<<2) | (1<<1) | (1<<0) )) & 0xFF # Clear bits 2/1/0
        controlData |= overSampleAmount << 0 # Align overSampleAmount to bits 2/1/0
        self._i2c.writeByte(self.address, self.BME280_CTRL_HUMIDITY_REG, controlData)

        self.set_mode(originalMode) # Return to the original user's choice

    humidity_oversample = property()
    humidity_oversample = humidity_oversample.setter(set_humidity_oversample)

    #----------------------------------------------------------------
    # Validates an over sample value
    # Allowed values are 0 to 16
    # These are used in the humidty, pressure, and temp oversample functions
    #
    # pylint: disable=no-self-use
    def check_sample_value(self, userValue):
        """!
        Validates an over sample value

        @param userValue: The oversample value to check.
                Allowed values are 0 to 16
                These are used in the humidty, pressure, and temp oversample functions

        @return **int** Valid oversample value
        """
        _valueMap = { 0: 0, 1: 1, 2: 2, 4: 3, 8: 4, 16: 5}

        return _valueMap[userValue] if userValue in _valueMap.keys() else 1

    # pylint: enable=no-self-use
    # Check the measuring bit and return true while device is taking measurement
    def is_measuring(self):
        """!
        Return if the sensor is measuring or not

        @return True if the sensor is measuring, else False
        :rvalue: boolean
        """

        stat = self._i2c.readByte(self.address, self.BME280_STAT_REG)
        return  True if stat & (1<<3) else False # If the measuring bit (3) is set, return true


    # Strictly resets.  Run .begin() afterwards
    def reset( self ):
        """!
        Resets the sensor. If called, the begin method must be called before
        using the sensor.
        """
        self._i2c.writeByte(self.address, self.BME280_RST_REG, 0xB6)

    # ****************************************************************************#
    #
    #   Pressure Section
    #
    # ****************************************************************************#
    def read_pressure( self ):
        """!
        Returns pressure in Pa.

        @return **float** Pressure in Pa
        """

        # Read temperature to update t_fine
        self.get_temperature_celsius()

        data_buffer = self._i2c.readBlock(self.address, self.BME280_PRESSURE_MSB_REG, 3)
        adc_P = (data_buffer[0] << 12) | (data_buffer[1] << 4) | ((data_buffer[2] >> 4) & 0x0F)

        var1 = self.t_fine - 128000
        var2 = var1 * var1 * self.calibration["dig_P6"]
        var2 = var2 + ((var1 * self.calibration["dig_P5"])<<17)
        var2 = var2 + (self.calibration["dig_P4"] <<35)
        var1 = ((var1 * var1 * self.calibration["dig_P3"])>>8) + ((var1 * self.calibration["dig_P2"])<<12)
        var1 = ( (1 << 47) + var1 )*(self.calibration["dig_P1"])>>33

        if var1 == 0:
            return 0  #  avoid exception caused by division by zero

        p_acc = 1048576 - adc_P
        p_acc = (((p_acc<<31) - var2)*3125)//var1

        var1 = ((self.calibration["dig_P9"]) * (p_acc>>13) * (p_acc>>13)) >> 25
        var2 = ((self.calibration["dig_P8"]) * p_acc) >> 19
        p_acc = ((p_acc + var1 + var2) >> 8) + ((self.calibration["dig_P7"])<<4)

        return p_acc / 256.0

    pressure = property(read_pressure)

    #----------------------------------------------------------------
    # Sets the internal variable _referencePressure so the
    def set_reference_pressure(self, refPressure):
        """!
        Sets the referance pressure for the sensor measurments.

        @param refPressure: The referance pressure to use.

        @return No return value
        """
        self._referencePressure = float(refPressure)

    # Return the local reference pressure
    def get_reference_pressure(self):
        """!
        Get the current reference pressure for the sensor.

        @return **float** The current reference pressure.
        """
        return self._referencePressure

    reference_pressure = property(get_reference_pressure, set_reference_pressure)

    #----------------------------------------------------------------
    def get_altitude_meters( self ):
        """!
        Return the current Altitude in meters

        @return **float** The current altitude in meters
        """

        return (-44330.77)*(math.pow((self.pressure/self._referencePressure), 0.190263) - 1.0) # Corrected, see issue 30

    altitude_meters = property(get_altitude_meters)

    #----------------------------------------------------------------
    def get_altitude_feet( self ):
        """!
        Return the current Altitude in feet

        @return **float** The current altitude in feets
        """
        return self.get_altitude_meters() * 3.28084

    altitude_feet = property(get_altitude_feet)


    # ****************************************************************************#
    #
    #   Humidity Section
    #
    # ****************************************************************************#
    def read_humidity( self ):
        """!
        Returns humidity in %RH.

        @return **float** The current humidity value
        """

        # Read temperature to update t_fine
        self.get_temperature_celsius()

        data_buffer = self._i2c.readBlock(self.address, self.BME280_HUMIDITY_MSB_REG, 2)
        adc_H = (data_buffer[0] << 8) | data_buffer[1]

        var1 = (self.t_fine - 76800)
        var1 = (((((adc_H << 14) - ((self.calibration["dig_H4"]) << 20) - ((self.calibration["dig_H5"]) * var1)) + \
            (16384)) >> 15) * (((((((var1 * (self.calibration["dig_H6"])) >> 10) * (((var1 * (self.calibration["dig_H3"])) >> 11) + (32768))) >> 10) + (2097152)) * \
            (self.calibration["dig_H2"]) + 8192) >> 14))
        var1 = (var1 - (((((var1 >> 15) * (var1 >> 15)) >> 7) * (self.calibration["dig_H1"])) >> 4))
        var1 = 0 if var1 < 0 else  var1
        var1 = 419430400 if var1 > 419430400 else var1


        return (var1>>12) / 1024.0

    humidity = property(read_humidity)

    # ****************************************************************************#
    #
    #   Temperature Section
    #
    # ****************************************************************************#

    def get_temperature_celsius( self ):
        """!
        Returns temperature in DegC and updates t_fine (needed for accurate
        pressure and humidity measurements)

        @return **float** The current temperature in C.
        """

        # get the reading (adc_T);

        data_buffer = self._i2c.readBlock(self.address, self.BME280_TEMPERATURE_MSB_REG, 3)
        adc_T = (data_buffer[0] << 12) | (data_buffer[1] << 4) | ((data_buffer[2] >> 4) & 0x0F)

        # By datasheet, calibrate

        var1 = ((((adc_T>>3) - (self.calibration["dig_T1"]<<1))) * (self.calibration["dig_T2"])) >> 11
        var2 = (((((adc_T>>4) - (self.calibration["dig_T1"])) * ((adc_T>>4) - (self.calibration["dig_T1"]))) >> 12) * \
                (self.calibration["dig_T3"])) >> 14
        self.t_fine = var1 + var2
        output = (self.t_fine * 5 + 128) >> 8

        return output / 100 + _settings["tempCorrection"]

    temperature_celsius = property(get_temperature_celsius)

    #----------------------------------------------------------------
    def get_temperature_fahrenheit( self ):
        """!
        Returns temperature in Deg F and updates t_fine (needed for accurate
        pressure and humidity measurements)

        @return **float** The current temperature in F.
        """
        output = self.temperature_celsius
        return (output * 9) / 5 + 32

    temperature_fahrenheit = property(get_temperature_fahrenheit)

    # ****************************************************************************#
    #
    #   Dew point Section
    #
    # ****************************************************************************#
    #  Returns Dew point in DegC

    def get_dewpoint_celsius(self):
        """!
        Returns the Dew point in degrees C.

        @return **float** The current dewpoint in C.
        """
        celsius = self.get_temperature_celsius()
        humidity = self.read_humidity()
        #  (1) Saturation Vapor Pressure = ESGG(T)

        RATIO = 373.15 / (273.15 + celsius)
        RHS = -7.90298 * (RATIO - 1)
        RHS += 5.02808 * math.log10(RATIO)
        RHS += -1.3816e-7 * (math.pow(10, (11.344 * (1 - 1/RATIO ))) - 1)
        RHS += 8.1328e-3 * (math.pow(10, (-3.49149 * (RATIO - 1))) - 1)
        RHS += math.log10(1013.246)
               #  factor -3 is to adjust units - Vapor Pressure SVP * humidity
        VP = math.pow(10, RHS - 3) * humidity
               #  (2) DEWPOINT = F(Vapor Pressure)
        T = math.log(VP/0.61078)   #  temp var
        return (241.88 * T) / (17.558 - T)

    dewpoint_celsius = property(get_dewpoint_celsius)

    #----------------------------------------------------------------
    #  Returns Dew point in DegF
    def get_dewpoint_fahrenheit(self):
        """!
        Returns the Dew point in degrees F.

        @return **float** The current dewpoint in F.
        """
        return self.get_dewpoint_celsius() * 1.8 + 32 # Convert C to F

    dewpoint_fahrenheit = property(get_dewpoint_fahrenheit)